CS/IT MCQ Collections

MCQ Questions On Data Transmission Techniques Part-2

Pinterest LinkedIn Tumblr
This set of MCQ questions on data transmission techniques includes the collections of the top 20 multiple-choice questions on the different data transmission techniques. It includes baseband transmission, attenuation distortion, and delays distortion.

1. ……………… means sending a digital signal over a channel without changing the digital signal to an analog signal.
A) Baseband transmission
B) Broadband transmission
C) Digital transmission
D) Analog transmission

2. In …………………. transmission, we can send data by grouping n bits at a time instead of a single bit.
A) parallel
B) serial
C) analog
D) digital

3. In ………………….. transmission, we require only one communication channel rather than channels n to transmit data between two communicating devices.
A) parallel
B) serial
C) analog
D) digital

4. ……………… is the loss of energy as the signal propagates outward, where the amount of energy depends on the frequency.
A) Noise
B) Delay distortion
C) Attenuation distortion
D) Dispersion

5. If the ……………….. is too much, the receiver may not be able to detect the signal at all or the signal may fall below the noise level.
A) Noise
B) Delay
C) Dispersion
D) Attenuation

6. Attenuation can be also expressed in decibel(dB) and commonly used because.
i) Signal strengths often fall off logarithmically
ii) Cascade losses and gains can be calculated with simple additions and subtractions
A) i only
B) ii only
C) Both of the above
D) None of the above

7. ……………… occurs due to velocity of propagation the frequency varies. Thus various frequency components of a signal arrive at the receiver at different times.
A) Noise
B) Delay distortion
C) Attenuation distortion
D) Dispersion

8. ………….. can be defined as unwanted energy from source other than the transmitter.
A) Dispersion
B) Attenuation Distortion
C) Delay distortion
D) Noise

9. …………… noise is caused by the random motion of the electrons in a wire and is avoidable.
A) Thermal
B) Intermodulation
C) Cross talk
D) Impulse

10. Thermal noise is often  referred to as …………… noise, because it affects uniformly the different frequencies.
A) Black
B) White
C) Gray
D) Blue


11.  ………………….. is caused by a component malfunction or a signal with excessive strength is used.
A) Thermal
B) Intermodulation
C) Cross talk
D) Impulse

12. ……………….. is a noise where foreign signal enters the path of the transmitted signal.
A) Thermal
B) Intermodulation
C) Cross talk
D) Impulse

13. …………….. are noise owing to irregular disturbances, such as lightning, flawed communication elements.
A) Thermal
B) Intermodulation
C) Cross talk
D) Impulse

14. ……………… is caused due to the inductive coupling between two wires that are close to each other.
A) Thermal
B) Intermodulation
C) Cross talk
D) Impulse

 15. Sometime when talking over the telephone, you can hear another conversation in the background which is ………………..
A) Thermal
B) Intermodulation
C) Cross talk
D) Impulse

16. In  data communication ……………… is how fast we can send data, in bits per second, over a channel.
A) data rate
B) data flow
C) data speed
D) baud rate

17. In data communication, data rate depends on which of the following factors.
i) The bandwidth available  ii) The level of the signals  iii) The level of noise
A) i and ii only
B) ii and iii only
C) i and iii only
D) All i, ii and iii

18. …………….. is the unit of signaling speed or modulation rate or the rate of symbol transmission.
A) Data rate
B) Bit rate
C) Signal to Noise Ratio
D) Baud rate

19. A …………… is a discrete time signal having finite number of amplitude.
A) Analog signal
B) Digital signal
C) Hybrid signal
D) Discrete signal

20. The range of frequencies that contain the information is called as the ………..
A) Bandwidth
B) Bit rate
C) Signal to Noise Ratio
D) Baud rate

Answers

1.  A) Baseband transmission
2. A) parallel
3. B) serial
4. C) Attenuation distortion
5. D) Attenuation
6. C) Both of the above
7. B) Delay distortion
8. D) Noise
9. A) Thermal
10. B) White
11. B) Intermodulation
12. C) Cross talk
13. D) Impulse 
14. C) Cross talk
15. C) Cross talk
16. A) data rate
17. D) All i, ii and iii
18. D) Baud rate
19. B) Digital signal
20. A) Bandwidth

Read Next: MCQ Questions On Data Transmission Techniques Part-3

Please follow and like us:
RSS
Follow by Email
X (Twitter)
Visit Us
Follow Me
YouTube
YouTube
LinkedIn
linkedIn | MCQ Questions On Data Transmission Techniques Part-2
Share

Author

Shuseel Baral is a web programmer and the founder of InfoTechSite has over 8 years of experience in software development, internet, SEO, blogging and marketing digital products and services is passionate about exceeding your expectations.

Write A Comment

RSS
Follow by Email
X (Twitter)
Visit Us
Follow Me
YouTube
YouTube
LinkedIn
Share